| |
RoentDek PRODUCT LIST
FRONT-END ELECTRONICS FOR ANALOG SIGNAL PROCESSING
|
| |
|
|
|
| |
Product
number
|
Product
Description |
|
| |
130 |
FAMP8c: 8-channel fast timing amplifier unit for detector signals from MCP, delay-line anode or other electron multiplier devices, gain about 70 (adjustable) inverting and non-inverting outputs via lemo 00/250 connectors, 50Ohm impedance. Typical bandwidth 80/200 MHz. 19” rack case with external mains power adapter (100-250VAC). For advanced detector read-out use with standard CFDs or fast ADC systems, e.g. in combination with FT4/12/16-TP.
DESCRIPTION SHEET MANUAL |
| |
 |
| |
|
|
|
| |
131 |
FAMP1+: single channel fast timing amplifier unit for amplification of fast detector signals(as from MCP, delay-line anode, channeltron, photo-multiplier, etc.), nominal gain about 70 (adjustable from 0-120%), positive or negative input, bandwidth 200 or 300 MHz, both inverting and non-inverting output via lemo00 connectors. Single box unit incl. mains adapter (100-250V AC).
DESCRIPTION SHEET MANUAL |
 |
| |
|
|
|
| |
134 |
FAMP3(b): 3-channel fast timing amplifier unit with adjustable gain and reconfigurable bandwidth/input impedance, inverting and non-inverting outputs, 3HU case with external mains adapter (100-250V AC).
DESCRIPTION SHEET MANUAL
|
| |
|
|
|
| |
134² |
FAMP6L: as FAMP3 but with 6 channels (twinFAMP3). Also available as NIM unit FAMP6. |
| |
|
|
|
| |
|
|
|
| |
136 |
LET1+: fast leading edge amplifying discriminator for counting, coincidence detection or medium resolution timing tasks. Single box unit incl. mains adapter (100-250V AC). For signals from secondary electron amplifiers such as MCP; PMT or Channeltrons, positive or negative input polarity (please specify). Output NIM or TTL (please specify at time of order)
DESCRIPTION SHEET MANUAL
|
| |
|
|
|
| |
164 |
LA1: 100 MHz (LV)TTL / NIM level signal converter.
DESCRIPTION SHEET
|
|
| |
|
|
|
| |
139 |
ATR19-2b: 2-channel front-end electronics: (amplifier and Constant Fraction discriminator with NIM output (optional ECL) for DLD-detectors in combination with FT4/12/16-TP-type connectors. 3HU case with external mains adapter (100-250V AC). Read-out of a DLD requires two units (one per anode layer) and a FAMP1 + CFD1c (or x) set for the MCP signal.
DESCRIPTION SHEET |
|
| |
|
|
|
| |
141 |
MIXA2: 2-channel analog signal mixing amplifier. Multi-purpose module for signal shaping, mixing and multiplexing. Signal input/output via Lemo connector (50 Ohm). 3HU case with external mains adapter (100-250V AC).Also useful for NIM signals, e.g. as “Fan in”.
DESCRIPTION SHEET |
|
| |
|
|
|
| |
145 |
BFAMP3: 3-channel fast timing amplifier unit with adjustable gain and reconfigurable bandwidth/input impedance, inverting and non-inverting bipolar-shaped outputs (shaping delay by cable bridge), 3HU case with external mains adapter (100-250V AC).
DESCRIPTION SHEET |
|
| |
|
|
|
| |
146 |
BFAMP1: as BFAMP3 but with one channel only. |
|
| |
|
|
|
| |
147 |
BFAMP8c: as FAMP8c but with bipolar-shaped outputs (like BFAMP1 and BFAMP3) |
|
| |
|
|
|
| |
148 |
VL1: active protection amplifier to delimit excessive signal height for subsequent circuits.
DESCRIPTION SHEET |
|
| |
|
|
|
| |
150 |
CFD8c: 8-channel constant fraction discriminator for advanced detector operation in combination with FAMP-type amplifiers. 19" rack case (1HU) with external mains power adapter(100-250VAC). Multi-hit dead-time 10 ns for fast signals (e.g. MCP signal). 300 MHz bandwidth, adjustable threshold, walk, delay, fraction ratio. Analog and digital monitor outputs, gating. NIM (ECL optional) timing outputs with adjustable signal width.
MANUAL |
 |
| |
|
|
| |
151 |
CFD4c: constant fraction discriminator like 150, but with 4 channels and a single width NIM unit. Requires a NIM-bin (with +/-6V) or SPS3 for operation, not included.*
MANUAL |
| |
|
|
|
| |
384 |
SPS3: can power up to two CFD4cX |
| |
|
|
| |
152 |
CFD1c: single-channel version of CFD8c. 3HU case with external mains adapter (100-250V AC).
MANUAL
|
| |
|
|
| |
154 |
CFD1x: single-channel CFD incl. pulse-height to NIM pulse-width converter for measuring signal pulse height and signal timing. 3HU case with external mains adapter (100-250V AC).
MANUAL |
| |
|
|
| |
155 |
CFD7x: 7-channel constant fraction discriminator incl. pulse-height to NIM pulse-width converter for one channel (as CFD1x) and 6 channels as in CFD8c, 19" rack case (1HU) as CFD8c.
MANUAL |
| |
|
|
| |
159 |
iUSB-IO2: upgrade option in CFD8c/7x for remote control of threshold settings
|
| |
|
|
| |
170 |
APG1: test pulser for testing and calibration of electronic modules and delay-line anodes. Provides Nim pulses and attenuated pulses (40 dB) with adjustable repetition rate and width. Single box powered via USB-port (or external +5V source, e.g. battery).
DESCRIPTION SHEET |
|
| |
|
|
