| |
RoentDek PRODUCT LIST
FRONT-END ELECTRONICS FOR ANALOG SIGNAL PROCESSING
|
| |
|
|
|
| |
Product
number
|
Product
Description |
|
| |
130 |
FAMP8c: 8-channel fast timing amplifier unit for detector signals from MCP, delay-line anode or other electron multiplier devices, gain about 55, adjustable within +/- 10% (0-110%) for 6 (2) channels, unipolar input, inverting and non-inverting outputs via lemo 00/250 connectors, 50Ohm impedance, bandwidth 200MHz. 19" rack case with external mains power adapter (100-250VAC). For advanced detector read-out use with standard CFDs or fast ADC systems, e.g. in combination with FT4/12/16-TP.
DESCRIPTION SHEET MANUAL |
| |
 |
| |
|
|
|
| |
131 |
FAMP1+: single channel fast timing amplifier unit for amplification of fast detector signals (similar to FAMP8). Single box unit incl. external mains adapter (100-250V AC).
DESCRIPTION SHEET MANUAL |
 |
| |
|
|
|
| |
133 |
PreFAMP6: 6-channel fast timing preamplifier unit with 5x gain, reconfigurable bandwidth and input impedance. Single box unit incl. external mains adapter (100-250V AC).
DESCRIPTION SHEET MANUAL |
| |
|
|
|
| |
134 |
FAMP3(b): 3-channel fast timing amplifier unit with adjustable gain and reconfigurable bandwidth/input impedance, inverting and non-inverting outputs, 3HU case with external mains adapter (100-250V AC).
DESCRIPTION SHEET MANUAL |
| |
|
|
|
| |
134² |
FAMP6L: as FAMP3 but with 6 channels (twinFAMP3) |
|
| |
|
|
|
| |
135 |
(D)FAMP6(b): 6-channel fast (Differential) timing amplifier unit with adjustable gain and reconfigurable bandwidth/input impedance, inverting and non-inverting outputs, as single width NIM unit. Requires NIM bin or special mains adaptor for operation, not included.
DESCRIPTION SHEET MANUAL |
| |
|
|
|
| |
136 |
LET1+: leading edge discriminator for counting, coincidence detection or low resolution timing tasks. Single box unit incl. mains adapter (100-250V AC). Input signal from RoentDek DET MCP front end via FT4TP (positive polarity). Output NIM or TTL (please specify). Timing resolution < 5 ns.
DESCRIPTION SHEET MANUAL
|
|
| |
|
|
|
| |
164 new |
LA1: 100 MHz (LV)TTL / NIM level signal converter.
DESCRIPTION SHEET
|
|
| |
|
|
|
| |
139 |
ATR19-2b: 2-channel standard front-end electronics (amplifier and constant fraction discriminator) in a 3HU case with external mains adapter (100-250V AC) for RoentDek delay-line detectors in combination with FT4/12/16-TP-type connectors. Readout of a DLD anode requires two units (one per layer) and a FAMP1+CFD1c (or x) set for the MCP signal.
DESCRIPTION SHEET |
|
| |
|
|
|
| |
141 |
MIXA2: 2-channel analog signal mixing amplifier. Multi-purpose module for signal shaping, mixing and multiplexing. Signal input/output via Lemo connector (50 Ohm). 3HU case with external mains adapter (100-250V AC).
DESCRIPTION SHEET |
|
| |
|
|
|
| |
145 (new) |
BFAMP3: 3-channel fast timing amplifier unit with adjustable gain and reconfigurable bandwidth/input impedance, inverting and non-inverting bipolar-shaped outputs (shaping delay by cable bridge), 3HU case with external mains adapter (100-250V AC).
DESCRIPTION SHEET |
|
| |
|
|
|
| |
146 |
BFAMP1: as BFAMP3 but with one channel only. |
|
| |
|
|
|
| |
150 |
CFD8c: 8-channel constant fraction discriminator for advanced detector operation in combination with FAMP-type amplifiers. 19" rack case (1HU) with external mains power adapter (100-250VAC). Multi-hit dead-time 10 ns for fast signals (e.g. MCP signal). 300 MHz bandwidth, adjustable threshold, walk, delay, fraction ratio. Analog and digital monitor outputs, gating. NIM (ECL optional) timing outputs with adjustable signal width.
MANUAL |
 |
| |
|
|
| |
151 |
CFD4c: constant fraction discriminator like 150, but with 4 channels and a single width NIM unit. Requires a NIM-bin (with +/-6V) or SPS3 for operation, not included.*
MANUAL |
| |
|
|
|
| |
384 |
SPS3: can power up to two CFD4cX |
| |
|
|
| |
152 |
CFD1c: single-channel version of CFD8c. 3HU case with external mains adapter (100-250V AC).
MANUAL
|
| |
|
|
| |
154 |
CFD1x: single-channel CFD incl. pulse-height to NIM pulse-width converter for measuring signal pulse height and signal timing. 3HU case with external mains adapter (100-250V AC).
MANUAL |
| |
|
|
| |
155 |
CFD7x: 7-channel constant fraction discriminator incl. pulse-height to NIM pulse-width converter for one channel (as CFD1x) and 6 channels as in CFD8c, 19" rack case (1HU) as CFD8c.
MANUAL |
| |
|
|
